EN 10089 Grade 60CrMo3-3 quenched and tempered (+QT)
EN 10089 Grade 60CrMo3-3 quenched and tempered (+QT) introduction
The steel 60CrMo3-3 is used for hot formed springs (torsion springs, coil springs, tension and compression springs) for high stress in the vehicle engineering.
Equivalent material: ISO 60CrMo3-3, JIS SUP13, KS SPS13, ASTM A689, SAE 4161, UNS G41610, DIN 1.7241, DIN 60CrMo3-3, AFNOR 60CrMo3-3, BS 60CrMo3-3, BS 705A60, AISI 4161H, AISI 4161, SAE 4161H, EN 1.7241, ASTM 4161H, ASTM 4161, UNS H41610
EN 10089 Grade 60CrMo3-3 quenched and tempered (+QT) general
| Property |
Temperature |
Value |
Comment |
| Density |
23.0 °C |
Density of 7.8 - 7.9 g/cm³ |
Typical for Chromium Molybdenum Steel |
EN 10089 Grade 60CrMo3-3 quenched and tempered (+QT) thermal
| Property |
Temperature |
Value |
Comment |
| Coefficient of thermal expansion |
23.0 °C |
Coefficient of thermal expansion of 1.1E-5 - 1.4E-5 1/K |
Typical for Chromium Molybdenum Steel |
| Melting point |
- |
Melting point of 1382 - 1529 °C |
Typical for Chromium Molybdenum Steel |
| Specific heat capacity |
23.0 °C |
Specific heat capacity of 448 - 502 J/(kg·K) |
Typical for Chromium Molybdenum Steel |
| Thermal conductivity |
23.0 °C |
Thermal conductivity of 36 - 43 W/(m·K) |
Typical for Chromium Molybdenum Steel |
EN 10089 Grade 60CrMo3-3 quenched and tempered (+QT) chemical
| Property |
Value |
| Carbon |
Carbon of 0.56 - 0.64 % |
| Chromium |
Chromium of 0.7 - 1 % |
| Manganese |
Manganese of 0.7 - 1 % |
| Molybdenum |
Molybdenum of 0.25 - 0.35 % |
| Phosphorus |
Phosphorus of 0.03 % |
| Silicon |
Silicon of 0.4 % |
| Sulfur |
Sulfur of 0.025 % |
EN 10089 Grade 60CrMo3-3 quenched and tempered (+QT) mechanical
| Property |
Temperature |
Value |
Comment |
| Elastic modulus |
23.0 °C |
Elastic modulus of 200 - 215 GPa |
Typical for Chromium Molybdenum Steel |
| Elongation |
20.0 °C |
Elongation of 6 % |
- |
| Poisson's ratio |
23.0 °C |
Poisson's ratio of 0.29 [-] |
Typical for Chromium Molybdenum Steel |
| Reduction of area |
20.0 °C |
Reduction of area of 30 % |
- |
| Tensile strength |
20.0 °C |
Tensile strength of 1450 - 1750 MPa |
- |
| Yield strength Rp0.2 |
20.0 °C |
Yield strength Rp0.2 of 1300 MPa |
- |
Have confidence in the strength and durability of our steel materials.
-- Our promise
Similar or equivalent steel materials
Get a quote