EN 10088-1 Grade X1CrNiMoCuN25-25-5 solution annealed (+AT)
EN 10088-1 Grade X1CrNiMoCuN25-25-5 solution annealed (+AT) introduction
The austenitic material X1CrNiMoCuN25-25-5 is used in solution annealed condition in the form of warm rolled sheet, rods, wire rods and profiles. It is resistant to intercrystalline corrosion also in sensitized condition.
Equivalent material: ISO X1CrNiMoCuN25-25-5, ISO AN55A, ISO 4537-310-92-E, DIN 1.4537, AFNOR Z2NCDU25-25-05Az, EN 1.4537
EN 10088-1 Grade X1CrNiMoCuN25-25-5 solution annealed (+AT) general
| Property | Temperature | Value |
|---|---|---|
| Density | 20.0 °C | Density of 8.1 g/cm³ |
EN 10088-1 Grade X1CrNiMoCuN25-25-5 solution annealed (+AT) thermal
| Property | Temperature | Value | Comment |
|---|---|---|---|
| Coefficient of thermal expansion | 100.0 °C | Coefficient of thermal expansion of 1.5E-5 1/K | - |
| - | 300.0 °C | Coefficient of thermal expansion of 1.65E-5 1/K | - |
| Melting point | - | Melting point of 1230 - 1480 °C | Typical for Austenitic Stainless Steel |
| Specific heat capacity | 20.0 °C | Specific heat capacity of 500 J/(kg·K) | - |
| Thermal conductivity | 20.0 °C | Thermal conductivity of 14 W/(m·K) | - |
EN 10088-1 Grade X1CrNiMoCuN25-25-5 solution annealed (+AT) chemical
| Property | Value |
|---|---|
| Carbon | Carbon of 0.02 % |
| Chromium | Chromium of 24 - 26 % |
| Copper | Copper of 1 - 2 % |
| Manganese | Manganese of 2 % |
| Molybdenum | Molybdenum of 4.7 - 5.7 % |
| Nickel | Nickel of 24 - 27 % |
| Nitrogen | Nitrogen of 0.17 - 0.25 % |
| Phosphorus | Phosphorus of 0.03 % |
| Silicon | Silicon of 0.7 % |
| Sulfur | Sulfur of 0.01 % |
EN 10088-1 Grade X1CrNiMoCuN25-25-5 solution annealed (+AT) electrical
| Property | Temperature | Value |
|---|---|---|
| Electrical resistivity | 20.0 °C | Electrical resistivity of 8.5E-7 Ω·m |
EN 10088-1 Grade X1CrNiMoCuN25-25-5 solution annealed (+AT) mechanical
| Property | Temperature | Value | Comment |
|---|---|---|---|
| Elastic modulus | 20.0 °C | Elastic modulus of 195 GPa | - |
| - | 100.0 °C | Elastic modulus of 190 GPa | - |
| - | 200.0 °C | Elastic modulus of 182 GPa | - |
| - | 300.0 °C | Elastic modulus of 174 GPa | - |
| - | 400.0 °C | Elastic modulus of 166 GPa | - |
| - | 500.0 °C | Elastic modulus of 158 GPa | - |
| Elongation | 20.0 °C | Elongation of 35 % | - |
| Elongation A80, transverse | 20.0 °C | Elongation A80, transverse of 40 % | - |
| Elongation, transverse | 20.0 °C | Elongation, transverse of 30 - 40 % | - |
| Hardness, Brinell | 20.0 °C | Hardness, Brinell of 250 [-] | - |
| Hardness, Brinell, trans | 20.0 °C | Hardness, Brinell, trans of 250 [-] | - |
| Poisson's ratio | 23.0 °C | Poisson's ratio of 0.3 [-] | Typical for Austenitic Stainless Steel |
| Shear modulus | 23.0 °C | Shear modulus of 77 GPa | Typical for Austenitic Stainless Steel |
| Tensile strength | 20.0 °C | Tensile strength of 600 - 800 MPa | - |
| Tensile strength, transverse | 20.0 °C | Tensile strength, transverse of 600 - 800 MPa | - |
| Yield strength Rp0.2 | 20.0 °C | Yield strength Rp0.2 of 300 MPa | - |
| - | 100.0 °C | Yield strength Rp0.2 of 240 MPa | - |
| - | 150.0 °C | Yield strength Rp0.2 of 220 MPa | - |
| - | 200.0 °C | Yield strength Rp0.2 of 200 MPa | - |
| - | 250.0 °C | Yield strength Rp0.2 of 190 MPa | - |
| - | 300.0 °C | Yield strength Rp0.2 of 180 MPa | - |
| - | 350.0 °C | Yield strength Rp0.2 of 175 MPa | - |
| - | 400.0 °C | Yield strength Rp0.2 of 170 MPa | - |
| Yield strength Rp0.2, transverse | 20.0 °C | Yield strength Rp0.2, transverse of 290 - 300 MPa | - |
| Yield strength Rp1.0 | 20.0 °C | Yield strength Rp1.0 of 340 MPa | - |
| - | 100.0 °C | Yield strength Rp1.0 of 270 MPa | - |
| - | 150.0 °C | Yield strength Rp1.0 of 250 MPa | - |
| - | 200.0 °C | Yield strength Rp1.0 of 230 MPa | - |
| - | 250.0 °C | Yield strength Rp1.0 of 220 MPa | - |
| - | 300.0 °C | Yield strength Rp1.0 of 210 MPa | - |
| - | 350.0 °C | Yield strength Rp1.0 of 205 MPa | - |
| - | 400.0 °C | Yield strength Rp1.0 of 200 MPa | - |
| Yield strength Rp1.0, transverse | 20.0 °C | Yield strength Rp1.0, transverse of 330 - 340 MPa | - |
Choose our top-tier steel products to elevate the quality and strength of your structures and equipment.
-- Our promise
Get a quote